Home / Guides
Guides
How to find what is in concrete before you drill, core or cut. Written for people who do the drilling, and checked against codes, manufacturers and safety agencies.
How radar sees into concrete, step by stepCompare scannersGlossary of scanning terms
- How to drill into concrete without hitting rebar, cables or pipesThe order of work careful drillers follow, from drawings to the first hole.8 min read
- How deep is rebar in a concrete wall or slab?Minimum cover in US and European codes, and what you actually find on site.7 min read
- How to read a concrete scanWhy a bar looks like an arch on GPR, how depth is measured, and what fools a scanner.7 min read
- GPR, wall detector or pocket scanner: which one do you need?Four kinds of tool, what each one sees, and which jobs need which.8 min read
- Drilling into a post-tensioned slab: what to do firstHow to tell a PT slab, why tendons are different, and who should scan it.6 min read
- You hit rebar while drilling. What now?How to tell, when to stop, and why cutting the bar is not your call.5 min read
- How to use Eagle XR: from unboxing to the first holeThe three official steps, the second line at 90 degrees, marking the wall, and what is not published.8 min read
- How to find plastic pipes and underfloor heating before you drillWhy metal detectors miss them, what finds them, and how deep heating pipes sit in a screed.8 min read
- Drilling into drywall, brick and block: what is behind it and how to checkStud spacing, cable zones by country, hollow block, lintels, and which detector suits which wall.9 min read
- Core drilling checklistA printable checklist for the hour before a core, an anchor or a saw cut.3 min read
- Drilling and scanning fibre-reinforced concreteWhere fibre concrete is used, how to tell, why steel fibres blur radar and cover meters, and what to do instead.6 min read
- Concrete scanning standards: which documents cover locating rebar and servicesACI, ASTM, BSI, DGZfP, the Concrete Society and HSE: what each document is for, and what a client means by "to standard".7 min read
- Drilling into hollowcore planks and precast floorsWhere the strands and cores are, what plank makers allow, fixings in the soffit, and what a scan can show.7 min read
- Drilling into a concrete slab on metal deckWhat radar sees from above and below, upper and lower flutes, hole sizes deck makers allow, and fixings in the soffit.7 min read
- Do stud finders work on concrete? Can they find rebar?Why density stud finders fail on concrete, how deep metal modes reach by the makers' figures, phone magnetometers, and what to use instead.7 min read
- X-ray concrete scanning: X-ray, GPR or a pocket scanner?What real concrete radiography needs, how GPR differs, published prices, and why Eagle XR is not an X-ray.6 min read
- How to mount a TV on a concrete wall without hitting cables, pipes or rebarSolid concrete, block or plasterboard on dabs: what bracket and anchor makers say, hiding the wires, and checking before you drill.8 min read
- Hanging kitchen cabinets on a concrete or block wallRails, hangers and fixings, what a loaded cabinet asks of the wall, where kitchen cables and pipes run, and checking first.8 min read
- Drilling into a concrete wall or ceiling in a condo or apartmentStrata, HOA and landlord rules, post-tensioned slabs, ceiling hooks, neighbours' services, noise hours, and when to ask the engineer.8 min read
- Where do cables and pipes run in walls and floors?UK safe zones and RCDs, US NEC protection, German DIN 18015-3 zones in walls, floors and ceilings, why concrete breaks the pattern, and how to check.9 min read
- I drilled into a wire or a water pipe. What now?First steps for a cable, a water or drain pipe, a gas pipe and underfloor heating, what RCDs and GFCIs do, and how to avoid it next time.8 min read
- Voids under a concrete slab: causes, signs, how they are found and fixedWhy the ground leaves a slab, the signs, radar and impulse-response surveys, finding pipes under a slab, filling or lifting, and when it is structural.8 min read
- Home inspector tools: what the standards require and what inspectors carryASHI, Texas and RICS rules on tools, the kit inspectors and surveyors carry, and where a concrete scanner does and does not fit.8 min read
- Concrete cover surveys: how a covermeter survey works and what the report showsNominal cover, how cover meters and GPR measure it, their limits, what a client gets in the report, and where a pocket scanner fits.8 min read