Home / Jobs / Kitchen fitters and appliance installers
Jobs for kitchen fitters and appliance installers
Kitchen fitting on concrete walls
Wall units, a core for the cooker hood duct, a vent for the tumble dryer, a tall housing for the oven, water and waste for the washing machine and the dishwasher. A kitchen wall carries a lot: the cooker supply, sockets above the worktop, the sink feeds, sometimes a gas pipe. One drilled pipe can mean a wet kitchen in the flat below.
Before you drill in a kitchen
Stop and call a competent person if
- a pipe near the hob may be gas and you cannot tell
- a circuit near the holes cannot be isolated
- the hood exhaust would go into a flue used by gas or other fuel appliances
The short version of this page. The details and sources follow below.
From Kitchen fitting on concrete walls: drillclear.com/jobs/kitchen-fitters-and-appliance-installers, where every step has its sources.
- US
- upper cabinets, range hood, duct, dryer vent, backsplash, rough-in
- UK
- wall units, cooker hood, extract, splashback, tall housing, waste

The jobs
01Wall units on a concrete or block wall
The fixings go in at one height along the whole run, right across the feeds rising from the sink and the cables to the sockets. Scan along the fixing line, with short lines across it at each bracket, before you mark it.
02The cooker hood duct core
A core through an outside wall, sized by the hood and the duct kit. Scan around it and both faces where you can.
03A dryer vent or an appliance waste
A small core through the whole wall, often low down, where water and waste pipes can also run.
Try the job in 3D
Tiles on a brick wall with two plastic pipes, a feed running across and the cable to a socket: the same picture as a splashback under a wall unit (the lab labels it a mirror cabinet). The tiles are our assumption, not Screening Eagle's.
One situation from the Scan lab, which has all eleven.
How pros do it
- Size the hood hole from the manual. Fisher & Paykel recommends 150 mm rigid or semi-rigid ducting, which needs a round hole of at least 160 mm in the ceiling or wall1. Caple tells installers to use the spigot size the hood states: a smaller duct cuts performance and voids the warranty2.
- Expect a cable near the duct. Fisher & Paykel also wants a power outlet within 750 mm of the motor assembly, on the wall, behind the chimney or in the ceiling1: the hood's own supply can sit right beside your core.
- Get the height, the extract rate and the flue right. Fisher & Paykel gives a minimum of 600 mm above a gas or electric cooktop1. Caple says to use the greatest distance stated, and recommends 650 mm for electric and 760 mm for gas2. In England, BEAMA's guide to Approved Document F gives, for homes with natural ventilation and intermittent extract fans, kitchens "60 l/s (or 30 l/s if the extract is a cooker hood)"; other ventilation systems have their own rates3. Exhaust air must not be discharged into an existing flue used by gas or other fuel appliances1.
- Dryer vents: short, straight, down. Indesit wants the vent hole directly behind the dryer, straight and pointing downwards, and the hose no longer than 2.4 metres4. ASKO's North American instructions allow only rigid or flexible metal duct for exhausting5.
From the trade sources listed below, opened 17 November 2026. They describe professional practice in general, not Eagle XR.


This side goes flat on the surface.
Where Eagle XR fits
- It lists plastic water pipes, including non-metallic PEX and PVC, electric cables and conduits, and rebar6: the things behind a kitchen wall. Materials: concrete (dry, normal or wet), drywall, and masonry (brick and block) in the App Store listing6; the product page says Eagle Intelligence is trained on concrete and learning more materials7.
- It shows the back of the element7. Hilti describes the same step for its tools: choose the drill bit length from the measured slab or wall thickness8.
- The product page gives 100 x 90 mm, made to fit in tight corners7: between a tall housing and the wall, or above a worktop.
- It scans one line at a time, in one direction: you slide it forward along the line, lift it, and start the next line.
Where it does not
- Tiles and splashbacks are not addressed in Screening Eagle's published facts, and Bosch names conductive wallpaper or tiles among the things that impair its own scanner9. Where you can, scan before the tiles go on.
- Copper and steel gas pipes: how the app shows them is not published. Treat any pipe near the hob as gas until you know otherwise, and keep clear.
- Whether a cable is live is not published either. Isolate the circuits you work near and treat every cable as live.
- Depth accuracy has not been published. Eagle XR is not a GPR: Screening Eagle calls it a first look for everyday work, to see whether a spot is clear or whether to call an expert. For investigations, mapping and reports, it points professionals to GPR systems7.
Questions kitchen fitters and appliance installers ask
Hanging kitchen cabinets on concrete walls: what goes wrong?Insurance guide
Mostly the holes, not the cabinets. One UK insurance site points out that a drill bit through a concealed pipe is a water claim, not a drilling claim10.
Core drill for a cooker hood: what size?Manufacturers
Take it from the hood and the duct kit, not from habit. One maker's numbers are in the first step above.
Cooker hood installation regulations: what applies?Manufacturers, BEAMA
The hood manual, the building regulations and the flue rule all apply. The heights, the extract rate and the flue rule are under How pros do it. BEAMA adds that a kitchen refurbishment "does not specifically require that extract ventilation is provided, but this should be considered good practice"3. The rules differ by country: check the ones where you work.
How do you drill the hole in the wall for a tumble dryer vent?Manufacturers
Follow the dryer's manual, then scan around the spot, both faces where you can reach them, before you core. The Indesit and ASKO rules are in the last step above.
Which tools do kitchen fitters use to find pipes and cables?Guide, manufacturer
One kitchen fitting guide lists a pipe detector and a power detector. It advises using one to check for hidden live cables and water or gas pipes before drilling11. Detectors have limits: Bosch writes that its own wall scanner does not display empty plastic pipes in one mode9.
We only install appliances. When does this matter?Product page, shop
It matters for the big holes, since most installs use the existing water, waste and power. The holes you do drill, a dryer vent, a waste through an outside wall, a hood duct, go through the whole wall and meet whatever lies in their path. The scanner is CHF 3,950, EUR 4,190, USD 4,830 or GBP 3,590, excluding VAT, import taxes and delivery7, with US sales tax added where it applies, and a used, activated or registered unit cannot be returned12: try the Scan lab first.
Anything else: search every answer on this site on Before you buy, or ask Screening Eagle directly.
Ready for your own job?
CHF 3,950per scanner, excluding VAT, import taxes and delivery. Ordering happens on Screening Eagle's shop.
Buy in Solar GoldPartner link: we may earn a commission. You pay Screening Eagle's normal price.
- Sold and shipped by Screening Eagle
- Same price in all four finishes
- Card, Apple Pay or Google Pay
- Express shipping from Switzerland. US orders ship from Pennsylvania
Sources
- Fisher & Paykel, installation guide, wall rangehoods HC60BCXB4, HC90BCXB4, HC90BCBB4, HC120BCXB4 (UK and Ireland), read 17 November 2026, fisherpaykel.com
- Caple, Extraction and Ventilation Guide 2025, read 17 November 2026, caple.co.uk
- BEAMA (UK trade association), Ventilation in new and existing homes: guide to Approved Document F 2021, read 17 November 2026, beama.org.uk
- Indesit, IDV 65 tumble dryer instruction booklet, via ManualsLib, read 17 November 2026, manualslib.com
- ASKO, TD76 vented tumble dryer installation instructions (North America), read 17 November 2026, partners.gorenje.com
- Apple App Store, Eagle XR listing by Screening Eagle Technologies AG, read 15 November 2026, apps.apple.com
- Screening Eagle, Eagle XR product page and FAQ, read 15 November 2026, xr.screeningeagle.com
- Hilti New Zealand, Typical Applications for Detection Systems, read 16 November 2026, hilti.co.nz
- Bosch, Wallscanner D-tect 200 C Professional, original instructions (2021), read 16 November 2026, homelectrical.com
- SimplyQuote, What Are Common Public Liability Insurance Claims for Tradesmen? (updated September 2026), read 17 November 2026, simplyquote.co.uk
- Designing Buildings Wiki, Installing a kitchen, read 17 November 2026, designingbuildings.co.uk
- Screening Eagle, official Eagle XR shop and return policy, read 14 November 2026, store.screeningeagle.com